var cvrrRRPlan_desc = "   The track plan is very simple - a loop with some side tracks, mostly in the center.  This will provide me with both simple switching and continuous operation.  The following image, as crude as it may be, shows the track plan along with the mountain and valley locations.";
var cvrrRRPlan_desc_thmb = cvrrRRPlan_desc;

var cvrr01_desc = "Here is a picture of the table top in its construction phase (it is sitting on top of my table saw).  At this point, I have not yet made the legs.  The front corner is where the control panel will be placed, and the underside has been painted.  My next steps are to make the legs and to add the foam surface.";
var cvrr01_desc_thmb = cvrr01_desc;

var cvrr02_desc = "In the lower left corner, the truss bridge is located over what will be the valley.";
var cvrr02_desc_thmb = cvrr02_desc;

var cvrr03_desc = "And a view from the right.  Not much to show here except maybe a better view of the legs.";
var cvrr03_desc_thmb = cvrr03_desc;

var cvrr10_desc = "Here we have a bird's eye view of the underpass.  The cork roadbed is in place so that I may properly layout and measure the depth of the underpass.";
var cvrr10_desc_thmb = cvrr10_desc;

var cvrr11_desc = "This is another view of the underpass.  I plan on building 'concrete retaining walls' on the vertical parts and lay asphalt for the road.";
var cvrr11_desc_thmb = cvrr11_desc;

var cvrr12_desc = "Here is the same shot but with more of the mountain in place.";
var cvrr12_desc_thmb = cvrr12_desc;

var cvrr13_desc = "Shown here is the beginning of the mountain.  To aid in the placement of the foam, I temporarily laid track inside the mountain.  Although it is not made yet, the valley will be just outside of the mountain.";
var cvrr13_desc_thmb = cvrr13_desc;

var cvrr14_desc = "If you look closely, you will notice the ‘Coffee Valley’ name on the train bridge.  It turned out good except for the fact that I put the decals on UPSIDE DOWN!  I had planed to use the two, glued together, Atlas Truss Bridges upside down.  But, when placing the decals, I put them on what would normally be the upright position.  So, I guess I will have to modify my plans instead of modifying the bridge.";
var cvrr14_desc_thmb = cvrr14_desc;

var cvrr15_desc = "This is an overall view of the fascia going around the control panel.";
var cvrr15_desc_thmb = cvrr15_desc;

var cvrr16_desc = "Here is a view of the fascia, the access hole, and the deep end of the valley.  The access hole will be covered with a flip down door.  The foam which forms the mountain is still removable, which is a good thing since the track is just temporarily pined in place.";
var cvrr16_desc_thmb = cvrr16_desc;

var cvrr19_desc = "In this photo, the mountain is removed so that I may begin work on the trestles and track which will be inside the mountain.  This also provides a good view of the mountain access hole.  The <a href='Model_Layouts_CVRR_SmallTrestle.html'>small trestle</a> will be on the left side of the photo and the larger one will be on the deeper end on the right side.";
var cvrr19_desc_thmb = cvrr19_desc;

var cvrr20_desc = "This is a good overall view of the mountain and valley from the deep end.  The trestle for this end will be a curved timber trestle.";
var cvrr20_desc_thmb = cvrr20_desc;